<button id="s233n"><button id="s233n"></button></button>
<xmp id="s233n"><form id="s233n"><button id="s233n"></button></form>
<form id="s233n"></form>
<xmp id="s233n"><form id="s233n"><form id="s233n"></form></form><xmp id="s233n"><form id="s233n"></form>
<xmp id="s233n"><form id="s233n"><button id="s233n"></button></form>
<xmp id="s233n"><form id="s233n"></form><form id="s233n"></form> <xmp id="s233n"><form id="s233n"></form><xmp id="s233n"><xmp id="s233n">
<xmp id="s233n"><form id="s233n"></form>
<xmp id="s233n">
<form id="s233n"><form id="s233n"><button id="s233n"></button></form></form>
<xmp id="s233n">
<xmp id="s233n"><form id="s233n"></form><form id="s233n"></form><xmp id="s233n">
<xmp id="s233n"><form id="s233n"></form>
<xmp id="s233n"><form id="s233n"></form><ins id="s233n"></ins><xmp id="s233n"><xmp id="s233n"><form id="s233n"></form><xmp id="s233n">
<xmp id="s233n"><xmp id="s233n"><form id="s233n"></form>
<xmp id="s233n"><form id="s233n"></form><xmp id="s233n"><form id="s233n"></form>
当前时间:
北京防水施工过程中,防水涂料涂刷要注意哪些方面?
作者:管理员    发布于:2023-03-07 16:50:19    文字:【】【】【
北京防水施工过程中,防水涂料涂刷要注意哪些方面?

1、刷涂时应先涂立面,后涂平面。在立面或平面涂布时,可采用分条或按顺序进行。分条进行时,每条宽度应与胎体增强材料宽度一致,以免操作人员踩踏刚涂好的涂层。流平性差的涂料,为便于抹压,加快施工进度,可以采用分条间隔施工的方法,待阴影处涂层干燥后,再抹空白处。

2、涂料涂布时涂刷致密是保证质量的关键。刷涂后续涂料则应按规定的涂层厚度(控制涂料的单方用量),均匀、仔细地刷涂。各道涂层之间的刷涂方向应相互垂直,以提高防水层的整体性和均匀性。涂层间的接槎,在每遍刷涂时应推槎50-100mm,接槎时应超过50-100mm,避免在搭接处发生渗漏。

3、刷涂时不能将气泡裹进涂层中,如遇气泡应立即消除。刷涂遍数必须按事先试验确定的遍数进行。切不可为了省事、省力而一遍刷涂过厚。前一遍涂料干燥后,方可进行下一层涂膜的刷涂。在前一遍涂层干燥后应将涂层上的灰尘、杂质清理干净后再进行后一遍涂层的涂刷,后遍涂料涂布前应严格检查前遍涂层是否有缺陷,如气泡、露底、漏刷、胎体增强材料皱翘边、杂物混入等现象,应先进行修补再涂布后遍涂层。

4、立面部位涂层应在平面涂布前进行,涂布次数应根据涂料的流平性好坏确定,流平性好的涂料应薄而多次进行,以不产生流坠现象为宜。以免涂层因流坠使上部涂层变薄,下部涂层变厚,影响涂膜的防水性能。

北京防水公司进行涂料粉刷时,通常采用滚筒刷或毛刷,主要针对流动性较好,施工厚度较薄的防水涂料,例如JS防水涂料,施工厚度通常1.5mm,分2-3遍刷涂至基层。
成人黄色网站在线观看_国产老妇伦国产熟女91_国产一级真人α爱做片浪潮_亚洲国产精品人人做人人爽
<button id="s233n"><button id="s233n"></button></button>
<xmp id="s233n"><form id="s233n"><button id="s233n"></button></form>
<form id="s233n"></form>
<xmp id="s233n"><form id="s233n"><form id="s233n"></form></form><xmp id="s233n"><form id="s233n"></form>
<xmp id="s233n"><form id="s233n"><button id="s233n"></button></form>
<xmp id="s233n"><form id="s233n"></form><form id="s233n"></form> <xmp id="s233n"><form id="s233n"></form><xmp id="s233n"><xmp id="s233n">
<xmp id="s233n"><form id="s233n"></form>
<xmp id="s233n">
<form id="s233n"><form id="s233n"><button id="s233n"></button></form></form>
<xmp id="s233n">
<xmp id="s233n"><form id="s233n"></form><form id="s233n"></form><xmp id="s233n">
<xmp id="s233n"><form id="s233n"></form>
<xmp id="s233n"><form id="s233n"></form><ins id="s233n"></ins><xmp id="s233n"><xmp id="s233n"><form id="s233n"></form><xmp id="s233n">
<xmp id="s233n"><xmp id="s233n"><form id="s233n"></form>
<xmp id="s233n"><form id="s233n"></form><xmp id="s233n"><form id="s233n"></form>